![3flybakcs/transformers high voltage 150W CO2 laser power supplies for 1850/2000mm CO2 laser tube](https://www.getatoz.co/assets/prodpic/1110189607br-130w02-co2-power-supply-1-.jpg)
3flybakcs/transformers high voltage 150W CO2 laser power supplies for 1850/2000mm CO2 laser tube from rubylasertech
3flybakcs/transformers high voltage 150W CO2 laser power supplies for 1850/2000mm CO2 laser tube
rubylasertech
$ 189 / Piece
BR-130W CO2 laser power supply
Feature:
1.The 220/110V CO2 power supply's control is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
2.The 130W CO2 power supply has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube's failure. It is very easy and simple to remove trouble.
3.Input analog signal(0~5V) or PWM is used to control the output laser power on this 130W CO2 power supply
4. The 220/110V CO2 power supply has H/L/P/G/IN/5V control signal port,The upper cover and bottom shell are aluminum shell is galvanized sheet.
5.The 130W CO2 power supply can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of 220/110V CO2 power supply and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.
6.The 130W CO2 power supply can match with EFR,Yongli,SPT, Weiju and other factories'160-165cm 130W sealed glass type CO2 laser tube. The 220/110V CO2 power supply uses zero-current half-bridge soft-switch circuit to make sure the CO2 power supply on laser cutter has high efficiency and fast response speed.
7. This130W CO2 power supply is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply
8.Each CO2 power supply on laser cutter before selling will go through the aging check:
(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;
(2) 500 times on/off check for 7 seconds.
9.The CO2 power supply on laser cutter is well grounded, which can ensure the safety of operators. At the same time, the 220/110v CO2 power supply also has an open circuit protection function, which allows the CO2 power supply on laser cutter to work for a short time in the open circuit state.
Specification:
Input Input voltage AC220V±10% (AC110V specified while order)
AC frequency 47~440HZ
Maximum input power 970W
Maximum input current 4.3A
Output Maximum output voltage 40KV
Maximum output current 36mA
(depending on the laser tubes of different manufacturers)
Efficiency More than 90% (Full load)
Response speed Not more than 1ms
Control lnterace TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation lnput-output AC 1500V 1 minutes not more than 10mA
lnput-shell AC 1500V 1 minutes not more than10mA
Output-shell Connection
Open Circuit Protection Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested Working temperature -10℃~50℃
Storage of temperature -20℃~75℃
Relative Humidity Maximum 85%RH (non-condensing)
Altitude 100,000 feet of work
200,000 feet of storage,dose not work
Cooling methods Forced air cooling (fan cooling)
Dimensions (LxWxH) 335mmx205mmx100mm
Feature:
1.The 220/110V CO2 power supply's control is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
2.The 130W CO2 power supply has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube's failure. It is very easy and simple to remove trouble.
3.Input analog signal(0~5V) or PWM is used to control the output laser power on this 130W CO2 power supply
4. The 220/110V CO2 power supply has H/L/P/G/IN/5V control signal port,The upper cover and bottom shell are aluminum shell is galvanized sheet.
5.The 130W CO2 power supply can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of 220/110V CO2 power supply and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.
6.The 130W CO2 power supply can match with EFR,Yongli,SPT, Weiju and other factories'160-165cm 130W sealed glass type CO2 laser tube. The 220/110V CO2 power supply uses zero-current half-bridge soft-switch circuit to make sure the CO2 power supply on laser cutter has high efficiency and fast response speed.
7. This130W CO2 power supply is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply
8.Each CO2 power supply on laser cutter before selling will go through the aging check:
(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;
(2) 500 times on/off check for 7 seconds.
9.The CO2 power supply on laser cutter is well grounded, which can ensure the safety of operators. At the same time, the 220/110v CO2 power supply also has an open circuit protection function, which allows the CO2 power supply on laser cutter to work for a short time in the open circuit state.
Specification:
Input Input voltage AC220V±10% (AC110V specified while order)
AC frequency 47~440HZ
Maximum input power 970W
Maximum input current 4.3A
Output Maximum output voltage 40KV
Maximum output current 36mA
(depending on the laser tubes of different manufacturers)
Efficiency More than 90% (Full load)
Response speed Not more than 1ms
Control lnterace TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation lnput-output AC 1500V 1 minutes not more than 10mA
lnput-shell AC 1500V 1 minutes not more than10mA
Output-shell Connection
Open Circuit Protection Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested Working temperature -10℃~50℃
Storage of temperature -20℃~75℃
Relative Humidity Maximum 85%RH (non-condensing)
Altitude 100,000 feet of work
200,000 feet of storage,dose not work
Cooling methods Forced air cooling (fan cooling)
Dimensions (LxWxH) 335mmx205mmx100mm
Browse Suppliers
Explore More Choices! Browse our full range of categories to compare similar products and discover the best suppliers for your business.
Get Verified Sellers Of Hand Tools
Get Verified Sellers Of Power Tool Accessories
Blades, Drill Accessories, Drill Bits, Milling Accessories, Sander Accessories
Get Verified Sellers Of Power Tools
Brazing Equipment, Drills, Grinders, Lathe Machine, Rotary Hammers