0-5V/PWM control Green wiring connection block 80W HV CO2 laser PSU for 1450mm 80W CO2 laser tube

rubylasertech

ZR-80WE CO2 POWER SUPPLIES
Feature
1. This high voltage laser power supplies’s control interface is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
2. Each 80Watt laser power supplies before selling will go through the aging check:
(1) sustain 10 hours at temperature 60 Degrees Celsius under full-load condition;
(2) 500 times on/off check for 7 seconds.
3. Input analog signal(0~5V) or PWM is used to control the output laser power on this 80Watt laser power supplies.
4. This 80Watt laser power supplies is used to drive most brands 1200-1450mm CO2 laser tube. The two fans laser power supplies use zero-current half-bridge soft-switch circuit to make sure the CO2 laser power supplies have high efficiency and fast response speed.
5.This two fans laser power supplies has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube’s failure. It is very easy and simple to remove trouble.
6. Aging check before stored in warehouse:
7. The CO2 laser power supplies have H/L/P/G/IN/5V control signal interface，The upper cover and bottom shell are made of aluminum Casing is galvanized sheet.
Specification
lnput  Input voltage AC220V±10% (AC110V specified while order)
AC frequency 47~440HZ
Maximum input power 750W
Maximum input current 3.4A
Output Maximum output voltage 32KV
Maximum output current 33mA
(depending on the laser tubes of different manufacturers)
Efficiency More than 90% (Full load)
Response speed Not more than 1ms
Control lnterace TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation lnput-output AC 1500V 1 minutes not more than 10mA
lnput-shell AC 1500V 1 minutes not more than10mA
Output-shell Connection
Open Circuit Protection Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested Working temperature -10℃~50℃
Storage of temperature -20℃~75℃
Relative Humidity Maximum 85%RH (non-condensing)
Altitude 100,000 feet of work
200,000 feet of storage,dose not work
Cooling methods Forced air cooling (fan cooling)
Dimensions (LxWxH) 283mmx178mmx106mm

ZR-80W LASER POWER SOURCES
Feature:
1. The 80W laser power supplies have good compatibility : The air cooling laser power supplies can work with most brand 1250mm,1400mm or 1450mm 80W or 90W glass laser tube,besides this feature, the network port laser power supplies also have strong adaptability and fast response, engraving or cutting benefits good effect.
2. The laser power control is simple, the network port laser power supplies can use 0-5V analog signal to control the laser power. Also the 80W laser power supplies can also use the PWM (pulse width modulation) signal for laser power control.
3. The air cooling laser power supplies have good protection function: The network port laser power supplies have open circuit protection to make the 80W laser power supplies to short-term work in the open state, so as to make it avoid the laser tube broken.
4. This 80W laser power supplies has simple control which selects high and low level for laser power control. The use of TTL-level control can realize start and stop. At the same time the air cooling laser power supplies add a protection switch, testing is made by external water and ventilation.
5. This 80W laser power supplies have stable laser output performance: Each air cooling power supplies have been much more testing procedures and under full load high temperature (52~55 degrees celsius) 24 hours of aging, which ensure the stability of each network port laser power supplies.
6. The ZR-80W laser power supplies uses ordinary H/L/P/G/IN/5V as laser control signal. And it uses aluminum top cover and galvanized plate bottom case
Specification
lnput  Input voltage AC220V±10% (AC110V specified while order)
AC frequency 47~440HZ
Maximum input power 750W
Maximum input current 3.4A
Output Maximum output voltage 32KV
Maximum output current 33mA
(depending on the laser tubes of different manufacturers)
Efficiency More than 90% (Full load)
Response speed Not more than 1ms
Control lnterace TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation lnput-output AC 1500V 1 minutes not more than 10mA
lnput-shell AC 1500V 1 minutes not more than10mA
Output-shell Connection
Open Circuit Protection Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested Working temperature -10℃~50℃
Storage of temperature -20℃~75℃
Relative Humidity Maximum 85%RH (non-condensing)
Altitude 100,000 feet of work
200,000 feet of storage,dose not work
Cooling methods Forced air cooling (fan cooling)
Dimensions (LxWxH) 283mmx178mmx106mm